Materials Science and Technology

Evaluation of interfacial fracture toughness of SiC fibre reinforced titanium-matrix composite using pushout test
pp. 561-566(6)
Authors: Yuan, M.N.; Yang, Y.Q.

On measurement of retained austenite in multiphase TRIP steels — results of blind round robin test involving six different techniques
pp. 567-574(8)
Authors: Jacques, P.J.; Allain, S.; Bouaziz, O.; De, A.; Gourgues, A.F.; Hance, B.M.; Houbaert, Y.; Huang, J.; Iza-Mendia, A.; Kruger, S.E.; Radu, M.; Samek, L.; Speer, J.; Zhao, L.; van der Zwaag, S.

Comparison of fatigue performance of HVOF spray coated and conventional roll bonded aluminium bearing alloys
pp. 575-581(7)
Authors: Ali, M.S.; Reed, P.A.S.; Syngellakis, S.

Performance evaluation of LSM-metallic interconnect composite films prepared by plasma sputtering method
pp. 582-586(5)
Authors: Chu, C.L.; Lee, S.; Lee, J.; Lee, T.H.

Electrical and field emission properties of multiwalled carbon nanotube/epoxy composites
pp. 587-590(4)
Authors: Zhao, B.; Wang, J.; Chen, D.; Zhang, Y.F.

Post-deposition treatment behaviour of zinc oxide thin films in hydrogen peroxide solution
pp. 591-594(4)
Authors: Arora, A.; George, P.J.; Dwivedi, V.K.; Gupta, V.

Investigation of tin penetration at bottom surface of float borosilicate glasses
pp. 595-598(4)
Authors: Liu, S.M.; Zhao, G.L.; Lin, X.H.; Ying, H.; Liu, J.B.; Wang, J.X.; Han, G.R.

Extremely fine and uniform microstructure of magnesium AZ91D alloy sheets produced by melt conditioned twin roll casting
pp. 599-606(8)
Authors: Bian, Zan; Bayandorian, I.; Zhang, H.W.; Scamans, G.; Fan, Z.

Preparation and tribological investigation of resin-matrix contact strip with variable current
pp. 607-613(7)
Authors: Chen, Z.H.; Tu, C.J.; Chen, D.; Xia, J.T.; Yan, H.G.

Influence of nitrogen on tensile properties of 316LN SS
pp. 614-618(5)
Authors: Ganesan, V.; Mathew, M.D.; Sankara Rao, K.B.

Study on iron purification from aluminium melt by Na₂B₄O₇ flux
pp. 619-624(6)
Authors: Gao, J.W.; Shu, D.; Wang, J.; Sun, B.D.

Role of second phase particles on microstructure and texture evolution of ARB processed aluminium sheets
pp. 625-631(7)
Authors: Pirgazi, H.; Akbarzadeh, A.

Fracture toughness for interfacial delamination of Cr-Mo steel multilayer laminate
pp. 632-635(4)
Authors: Pozuelo, M.; Cepeda-Jiménez, C.M.; Chao, J.; Carreño, F.; Ruano, O.A.

Simulation and application of dynamic heat transfer model for improvement of continuous casting process
pp. 636-639(4)
Authors: Ma, J.C.; Xie, Z.; Ci, Y.; Jia, G.L.

Comparison of residual stresses in Ti-6Al-4V and Ti-6Al-2Sn-4Zr-2Mo linear friction welds
pp. 640-650(11)
Authors: Frankel, P.; Preuss, M.; Steuwer, A.; Withers, P.J.; Bray, S.

RETRACTED ARTICLE

Room temperature hardness of carbide strengthened cast alloys in relation with their carbon content and aging temperature Part 1 - Case of nickel alloys
pp. 657-662(6)
Author: Berthod, P.

Room temperature hardness of carbide strengthened cast alloys in relation with their carbon content and aging temperature Part 2 - Case of cobalt alloys
pp. 663-669(7)
Author: Berthod, P.

Coupled heat and fluid flow model and experimental verification of aluminium plate die casting
pp. 670-679(10)
Authors: Taha, M.A.; El-Mahallawy, N.A.; El-Sabbagh, A.M.

Characterisation of interfacial imperfections of TiAl and 40Cr diffusion bonding by ultrasonic amplitude and phase
pp. 680-686(7)
Authors: Gang, T.; Luan, Y.L.; Zhao, X.M.; Xu, Z.Y.