Journal of the European Ceramic Society

Editorial Board
pp. CO2-CO2(1)

Comment on hardness definitions
pp. 1355-1359(5)
Author: Malzbender J.

Room and elevated temperature strength of perovskite membrane tubes
pp. 1361-1368(8)
Authors: Nagendra N.; Bandopadhyay S.

Exploring the polyvinyl alcohol method for preparing cuprates and manganites
pp. 1369-1373(5)
Authors: Calleja A.; Segarra M.; Serradilla I.G.; Capdevila X.G.; Fernandez A.I.; Espiell F.

Thermal decomposition products of the heteronuclear complex, LaNi(dhbaen)(NO₃)(H₂O)_n
pp. 1375-1381(7)
Authors: Aono H.; Kondo N.; Sakamoto M.; Traversa E.; Sadaoka Y.

The influence of concentration on the formation of BaTiO₃ by direct reaction of TiCl₄ with Ba(OH)₂ in aqueous solution
pp. 1383-1390(8)
Authors: Viviani M.; Buscaglia M.T.; Testino A.; Buscaglia V.; Bowen P.; Nanni P.

Characterization of CaTiO₃-NdAlO₃ dielectric ceramics
pp. 1391-1400(10)
Authors: Jancar B.; Suvorov D.; Valant M.; Drazic G.

R-curves of lead zirconate titanate (PZT)
pp. 1401-1408(8)
Authors: Karastamatis T.; Lupascu D.C.; dos Santos e Lucato S.L.; Rodel J.; Lynch C.S.

Unipolar fatigue of ferroelectric lead-zirconate-titanate
pp. 1409-1415(7)
Authors: Verdier C.; Lupascu D.C.; Rodel J.

Thermal and chemical induced expansion of La_0.3Sr_0.7(Fe,Ga)O_3- ceramics
pp. 1417-1426(10)
Authors: Kharton V.V.; Yaremchenko A.A.; Patrakeev M.V.; Naumovich E.N.; Marques F.M.B.

Internal stresses in BaTiO₃/Ni MLCCs
pp. 1427-1434(8)
Authors: Shin Y.-I.; Kang K.-M.; Jung Y.-G.; Yeo J.-G.; Lee S.-G.; Paik U.

Influence of a high conductivity additive on the electrical properties of vanadium dioxide-based ceramics
pp. 1435-1439(5)
Authors: Kolbunov V.R.; Ivon A.I.; Chernenko I.M.

Thick-film resistors on zirconia substrates for possible strain gauge applications
pp. 1441-1448(8)
Authors: Hrovat M.; Belavic D.; Bencan A.; Holc J.

Investigation of the thermomechanical properties of a plasma-sprayed nanostructured zirconia coating
pp. 1449-1455(7)
Authors: Chen H.; Zhou X.; Ding C.

Effect of silver doping on the phase transformation and grain growth of sol-gel titania powder
pp. 1457-1464(8)
Authors: Chao H.E.; Yun Y.U.; Xingfang H.U.; Larbot A.

Crystallization kinetics of mullite formation in diphasic gels containing different alumina components
pp. 1465-1475(11)
Authors: Tkalcec E.; Ivankovic H.; Nass R.; Schmidt H.

The influence of oxidation on crack resistance in injection moulded Cr₃C₂/Al₂O₃ composites
pp. 1477-1484(8)
Authors: Jeng C.-A.; Huang J.-L.

Densification and mechanical properties of mullite/TiO₂-coated B₄C composites
pp. 1485-1490(6)
Authors: Zhao H.; Hiragushi K.; Mizota Y.

Design, fabrication and properties of layered SiC/TiC ceramic with graded thermal residual stress
pp. 1491-1497(7)
Authors: Qin S.; Jiang D.; Zhang J.; Qin J.

Microstructure of SiC deposited from methyltrichlorosilane
pp. 1499-1508(10)
Authors: Reznik B.; Gerthsen D.; Zhang W.; Huttinger K.J.

Influence of SiC infiltration on some properties of porous carbon materials
pp. 1509-1515(7)
Authors: Kluska S.; Jonas S.; Walasek E.; Stapinski T.; Pyzalski M.

Effects of Li₂O on the low temperature sintering and thermal conductivity of AlN ceramics
pp. 1517-1524(8)
Authors: Qiao L.; Zhou H.; Chen K.; Fu R.

Effect of dispersant on the rheological properties and slip casting of concentrated sialon precursor suspensions
pp. 1525-1530(6)
Authors: Xu X.; Oliveira M.I.L.L.; Fu R.; Ferreira J.M.F.

Microstructural design of Ca -sialon ceramics: effects of starting compositions and processing conditions
pp. 1531-1541(11)
Authors: Zhang Y.; Cheng Y.-B.

Effect of the residual phases in -Si₃N₄ seed on the mechanical properties of self-reinforced Si₃N₄ ceramics
pp. 1543-1547(5)
Authors: Dai J.; Li J.; Chen Y.; Yang L.